Last updated
Prepare a measured pass
Use the mouse tester first if pointer motion feels erratic and you also suspect a middle button or wheel problem. For the DPI tester, you need a ruler, a flat mousepad, and enough clear space to move the device sideways in a straight line. Two inches is a practical starting distance. Five centimeters is another convenient choice if your ruler uses metric markings.
Pick a visible point on the mouse shell and make two marks on the desk or low-tack tape, one for the start and one for the end. For example, line the center of the wheel up with the first mark, then move until the same point lines up with the second mark. Keep the mouse facing the same direction. A ruler can be a visual guide or sit along the travel path, provided it does not lift one edge of the mouse.
Turn off operating-system pointer acceleration and any acceleration configured in the mouse utility before testing. On Windows, open Additional mouse settings → Pointer Options and clear Enhance pointer precision. On supported macOS versions, look for Pointer acceleration in System Settings → Mouse → Advanced. Write down your original settings if you plan to restore them. Microsoft mouse settings · Apple tracking settings
Measure and compare
- Enter the distance between the marks and select inches or centimeters. Add the DPI shown for the active stage in your mouse utility if you want a comparison.
- Put the mouse at the first mark before starting. Select Start raw test and wait for the browser to capture the cursor. The cursor is hidden while the tool measures relative movement.
- Move horizontally in one uninterrupted pass. Stop with the chosen point on the mouse at the second mark. Keep the mouse on the surface. Press Space, or leave the mouse in place and use the left button to finish.
- Write down the result, return to the start mark, and repeat. If the browser cancels capture, reposition the mouse and start over. Start at the end mark and measure back the other way to check your alignment.
The raw-mode calculation divides the magnitude of the net horizontal movement by the physical distance in inches. For metric input, the tool divides centimeters by 2.54 to get inches first. A two-inch pass and 1,600 horizontal counts give 800 DPI. If the active setting says 800 and the estimate is 760, the comparison is five percent lower. The sign shows direction of the difference from the entered claim, regardless of whether your pass went left or right.
Horizontal movement is signed until the final calculation. If you move past the mark and pull back, the backward counts subtract from the forward counts. Aim for one clean pass anyway. A reversal can introduce results that depend on how your mouse tracks the surface. The test does not add vertical travel because the ruler marks describe horizontal distance. A diagonal pass will generally produce a lower horizontal reading than the total motion along that diagonal.
What the measurement can and cannot show
The requested mode uses Pointer Lock with unadjusted movement so the browser can provide relative movement without clamping the cursor at the edge. Browser and platform support varies. Some browsers reject the request, and older implementations may accept a lock without confirming the raw option. A legacy lock gives relative units per inch. Think of a raw-mode estimate as a practical check of the configured mouse stage, with uncertainty from the browser, operating system, sensor surface, and ruler setup. W3C Pointer Lock specification
If raw capture is unavailable, the tester should switch you to the ruler fallback automatically and say so in the result note. You can also start that mode yourself with the cursor fallback control. Some browsers, locked-down profiles, and virtualized environments reject Pointer Lock, including a not-supported error when raw unadjusted movement is requested. The page catches that error and keeps the tool usable.
The fallback still uses the known distance you entered. Choose a distance short enough for the pointer to remain within the browser viewport. Start near the left edge of the measurement area, hold the left button, move the mouse to the end mark, then release. This mode reports CSS screen pixels per inch. Desktop scaling, browser zoom, OS sensitivity, and acceleration can influence it, so the tool leaves sensor-DPI comparison blank. Try a current desktop Chromium browser if you need the raw-mode comparison.
Several repeatable passes near the same value are more informative than one number. Try moving slowly and then at a moderate speed over the same distance. If those readings differ by a lot, check acceleration, the capture mode and the tracking surface. If every pass is close but consistently offset from the selected stage, write down the offset and compare another stage on the same mouse before drawing conclusions.
Troubleshoot a result that looks wrong
The result is close to double or half the claim. Check that the unit matches the ruler. For example, entering two centimeters for two inches would multiply the estimate by 2.54. See which mouse profile is active after you switch away from your game. Some devices have per-app DPI settings, and a sniper button or profile shortcut can change the current stage without changing the setting you last viewed.
The result changes by several percent between attempts. Keep the same shell reference point at both marks and try a longer pass. If you miss the end mark by one millimeter on a 50-millimeter pass, the distance is already off by about two percent. On a 100-millimeter pass the same error is about one percent. Leave extra space after the end mark so your hand can stop cleanly. Turn the mouse around as little as possible, and avoid lifting it during the pass.
The cursor skips or movement disappears mid-pass. Try the surface you normally use and a second matte pad. Clean obvious debris from the pad and the opening around the sensor, following the manufacturer’s care instructions. For a wireless mouse, compare with a charged battery and the receiver close by. If the trouble appears only in motion, use the mouse polling rate test to compare update cadence between connections.
The result looks plausible, but a game still feels different. Check the game’s input mode and sensitivity scale. The DPI tester measures mouse movement across the pad. Your in-game turn depends on how the game transforms that movement and on settings such as aiming sensitivity. eDPI is usually mouse DPI multiplied by the in-game sensitivity number, useful for comparison inside the same game. Comparing centimeters per full turn is often clearer across games with different scales.
A dirty lens, a glossy desk, or a pad with a strong pattern can also change how many counts you collect over the same ruler distance. If two pads disagree, record both surfaces and prefer the one you actually use. Lift-off height is a separate check: if the cursor keeps moving after you pick the mouse up a few millimeters, that will not usually change a flat pass, but it can spoil a measurement if you accidentally tilt or hop the mouse near the end mark.
When keeping results for your own records, include the profile, connection type, surface, ruler distance, direction, and browser. Take three straight passes and compare their middle value. If the mouse utility lets you set more than one stage, measuring two widely separated settings can help confirm that the mouse is switching stages as intended. Restore any acceleration settings you normally use after the test.
Frequently asked questions
What does DPI mean for a mouse?
Mouse DPI describes how many movement counts represent one inch of travel. Manufacturers also call this CPI, or counts per inch. Mouse software can expose several DPI stages for the same device.
How far should I move the mouse?
Start with two inches or about five centimeters in raw mode. Use a ruler and a fixed point on the mouse shell. A longer straight pass can reduce the effect of endpoint error if your mousepad has room.
Should pointer acceleration be off?
Yes. Disable operating-system pointer acceleration and any vendor acceleration for the measurement. If the reported result changes markedly when you vary your speed, check the input mode and settings before comparing it with the claim.
Does monitor resolution affect mouse DPI?
The sensor setting stays the same when you change your display. Cursor travel can change because screen scale, zoom, or pointer settings change how movement is rendered. Raw mode is the better comparison with a sensor setting.
What if the raw test cannot lock my pointer?
Try a current desktop Chromium browser in its own tab. If raw capture is still unavailable, cursor fallback can compare effective screen motion between passes. It displays CSS pixels per inch and leaves claimed DPI comparison blank.
Why did I measure 760 when my mouse says 800?
Repeat the pass both ways and verify the active stage, ruler marks, and input method. Endpoint error, surface behavior, or device variation can all shift a result. A single short pass cannot isolate those causes.
Is DPI the same as eDPI?
DPI describes the mouse setting. eDPI usually multiplies that setting by in-game sensitivity and is most useful within one game using one sensitivity scale.